Solar Boat wiring diagram and BOL

Solar System Diagram

Note: this page may contain affiliate links, for more information please click here 

The current boat system is comprised of the following materials:

– 1x 4 String PV Combiner Box
– 1xVictron Energy SmartSolar MPPT TR VE.Can 250V 100 amp 12/24/36/48-Volt Solar Charge Controller (Bluetooth)
– 1x Victron Energy Quattro 5000VA 24-Volt Pure Sine Wave Inverter 120 amp Battery Charger
– 1x Victron Color Control GX Monitor
– 1x Victron BMV-712 Battery Monitor
– 1x Victron Energy Orion IP20 24/12-Volt 70 amp DC-DC Converter Non-Isolated, High Power
– 1x MNSPD-300-AC Surge Protector Device -300V AC
– 1x Battery Disconnect Switch, 350A Battery Switch Single Circuit Power Disconnect Isolator ON/Off (optional)
– 1x 12VDC Blue Sea Systems ST Blade ATO/ATC Fuse Blocks
– 1x Negative 600 Amp Bus Bar 300V AC / 48V DC Copper Made Heavy-Duty Module Power Distribution Block with 8 x 3/8″ (M10)
– 1x Positive 600 Amp Bus Bar 300V AC / 48V DC Copper Made Heavy-Duty Module Power Distribution Block with 8 x 3/8″ (M10)
– 1x 80 Amp Circuit Breaker Trolling with Manual Reset, 12V- 48V DC, Waterproof (80A)
– 1x 150 Amp Surface-Mount Circuit Breakers with Manual Reset Switch Button for Boat Marine RV
– 2x 200 Amp Circuit Breaker Manual Reset with Switch Button for Boat Marine RV Yacht Battery Truck Solar, 12V – 48V DC, Waterproof
– 2x 300A Circuit Breaker with Manual Reset Fuse Holder for Marine Boat  with Wire Lugs Copper Washer
– 6x Positive 2/0 AWG Gauge RED Battery Cables Solar, RV, Car, Boat Tools (7 FEET,Both END 3/8)
– 6x Negative 2/0 AWG Gauge BLACK Battery Cables Solar, RV, Car, Boat Tools (7 FEET,Both END 3/8)
– 6x 200A Blue Sea Systems MEGA/ AMG Fuses
– 2x pairs 10 AWG Solar Panel Cable Wire 30 Ft Extension Cable RED & BLACK Weatherproof Female and Male Connector Adapter Kit( goes from panels to combiner box)
– 1x 10 FT Red & Black 8 Gauge Tinned Copper Electrical Wire (goes from PV combiner to charge controller)
– 1x 10 FT Red & Black 2 Gauge Tinned Copper Electrical Wire Cable (goes from charge controller to the positive and negative bus bars respectively)
– 1x 10 FT Red & Black 4 Gauge Tinned Copper Electrical Wire Cable (goes from the bus bars to 24-12 DC-DC converter and from DC-DC converter to 12V DC panel)
– 1x 2/0 AWG 10 Feet Red + 10 Feet Black Welding Battery Pure Copper Flexible Cable + 10pcs of 3/8″ Tinned Copper Cable Lug Terminal Connectors + 3 Feet Black Heat Shrink Tubing (goes from the two alternators to the bus bars and from bus bars to the inverter/charger)
– 1x Hammer Lug Crimper Tool V2 with holes for bench mounting (Crimps Battery and Welding cables 8 AWG TO 4/0 Wire Gauge) for crimping the cables as needed
– 2x Victron VE.Can Energy RJ45 UTP Cable, 5 Meter (goes from MPPT charge controller and inverter/charger to Color Control GX)
– 1x Victron Energy VE.Direct Cable, 9.84 ft (from BMV-712 to Color Control GX)
– 1x Ground wire Solid Bare Copper Grounding Wire, 4 AWG (goes from Combiner box and negative bus bar to the ground chassis)